RME - TDIF - 8-channel TDIF Interface incl. Wordclock, for DIGI-Series, HDSP 9652, HDSP 9632, HDSPe 9632

Brand:	RME
Model:	TDIF
Name:	TDIF - 8-channel TDIF Interface incl. Wordclock, for DIGI-Series, HDSP 9652, HDSP 9632, HDSPe 9632
Category:	Hardware > Interfaces > Add-On > Expansion Boards
Condition:	Brand New
List Price:	$299.00
Our Price:	$249.00
Your Price:	Click here to get a better price!
Availability:	Contact us
Buy:

Shipping Calculator:

Zip (Postal) Code:

Country:

No Sales Tax outside Florida
Contact us if you have an APO/FPO address
Contact us if your country is not listed here

Description:

8-channel TDIF Interface for ADAT-capable RME cards

The TEB (TDIF Expansion Board) adds an 8-channel TDIF interface to all ADAT-capable RME cards (see below). Special features include manual choice of clock reference, status LEDs and a word clock output.

The TEB is designed for maximum flexibility. Used with the Hammerfall series and the HDSP 9652, it can even be used at sample rates of 88.2 kHz and 96 kHz. Meeting the TDIF specification, Double Line mode uses two channels in single speed to get one channel in double speed. Therefore at 88.2/96 kHz 4 channels are available.

Installation is done in a convenient manner using the supplied bracket. No PCI slot on the motherboard is needed. The integrated Clock Select Switch sets the TDIF reference clock, thus avoids any clocking problems even with 'problematic' TDIF devices.

OPERATING THE EXBs

Using the Expansion Boards is very easy to do, thanks to the clearly structured and informative Settings dialog of RME's cards. The TEB operates like any other converter with ADAT input and output, but is connected internally. Therefore the input selector has to be set to 'Internal'.
The TEB gets its clock either from the card or the external TDIF device. This is selected via the switch at the slot bracket.

The Input Status displays the selected input (Internal), the current sample rate (44.1/48) and format (Adat.)

The ADAT output of all cards operate in parallel to this TDIF output. When Hammerfall or HDSP 9652 are operated in Double Speed mode, the TEB automatically converts the audio data to Double Line mode.

-NOTES ON COMPATIBILITY-

HDSP 9652

Two TEBs can be connected and operated simultaneously. One TEB can be used together with either one AEBx-I or AEBx-O.

DIGI96 SERIES

TEBs use the internal ADAT interface of the DIGI cards. Therefore they do not work with the DIGI96 (which did not support ADAT).

One TEB can be connected and operated.

HAMMERFALL DSP MULTIFACE / DIGIFACE

Multiface and Digiface use the Hammerfall DSP PCI card. This card has no internal inputs or outputs. Therefore no Expansion Boards can be used.

HAMMERFALL SERIES

An operation with the Hammerfall or Hammerfall Light requires board revision 1.5 or higher, because the internal connector ADAT1Out was not implemented in earlier versions.

One TEB can be connected and operated. Additionally one AEBx-O can be used simultaneously.

Features:

TDIF port: D-sub 25 pin
Supported sample rates: 44.1 kHz, 48 kHz, varispeed (33 - 57 kHz)
Double Line mode: 4 channels at 88.2 kHz and 96 kHz (not with DIGI96 series)
Word clock output: BNC, low-impedance driver stage, 4 Vss into 75 Ohms, short-circuit-proof
Power supply uses 3.5" floppy connector, 5 V DC, 100 mA
AEB needs no slot on the motherboard
Standard bracket, board dimensions AEB4: 75 x 95 mm
2 internal cable 2-pin, 1 internal cable 3-pin, 1 power adapter cable 5 1/4" to 2 x 3.5" included